Picture of Plastic Gears-LogoPlastic Gears-Yeh Der

Plastic Gear
Worm plastic Gears
Helical Plastic Gears
Pinion Plastic Gears
Spur Plastic Gears
Bevel Plastic Gears
Other Plastic Gears
Powder Metallurgy Gear
Production Equipment
Inspection Equipment
Injection Molding
΅@ Example 01
΅@ Example 02
΅@ Insert Molding
΅@ Automotive
΅@ Computer
΅@ Home Appliances
΅@ Heath Care
΅@ Remote Control
΅@ Meter
΅@ Decoration
Plastic Material
About Us
Contact Us
Catalogue Download

Plastic Material PA6
Plastic Material PA6

PA 6 (Polyamide 6, or Nylon 6, or Polycaprolactam)


Used in many structural applications because of its good mechanical strength and rigidity. It is used in bearings because of its good wear resistance.

Injection molding processing conditions


Since PA 6 absorbs moisture readily, care should be taken to ensure its dryness prior to molding. If the material is supplied in watertight packaging, the containers should be kept closed. If the moisture content is >0.2%, drying in a hot air oven at 80 C (176 F) for 16 hours is recommended. If the material has been exposed to air for more than 8 hours, vacuum drying at 105 C (221 F) for more than 8 hours is recommended. 

Melt Temperature  

230 - 280 C (446 - 536 F); 250 - 300 C (482 - 572 F) for reinforced grades 

Mold Temperature

80 - 90 C (176 - 194 F). Mold temperature significantly influences the crystallinity level which in turn affects the mechanical properties. For structural parts, a high degree of crystallization is required and mold temperatures of 80 - 90 C (176 - 194 F) are recommended. High mold temperatures are also recommended for thin-wall parts with long flow lengths. Increasing the mold temperature increases the strength and hardness, but the toughness is decreased. When the wall thickness is greater than 3 mm, a cold mold is recommended (20 - 40 C / 68 - 104 F), which leads to a higher and more uniform degree of crystallinity. Glass reinforced resins are always processed at mold temperatures greater than 80 C (176 F). 

Resin Injection Pressure

Generally between 750 - 1,250 bar (~11,000 - 18,000 psi) (depends on material and product design) 

Injection Speed

High (slightly lower for reinforced grades) 

Runners and Gates

The gate location is important because of very fast freeze-off times. Any type of gate may be used; the aperture should not be less than half the thickness of the part. When hot runners are used, the size of the gates can be smaller than when cold runners are used, because premature freeze-off is prevented. When using submarine gates, the minimum diameter of the gate should be 0.75 mm.

Chemical and Physical Properties

The molecular structure of polyamides consist of amide (CONH) groups joined by linear aliphatic sections (based on methylene groups). The toughness, rigidity, crystallinity, and thermal resistance of polyamide resins are due to the strong interchain attraction caused by the polarity of the amide groups. The CONH groups also cause a lot of moisture absorption.
Nylon 6 is produced by polymerization of caprolactam. The chemical and physical properties are similar to that of PA 66. However, its melting point is lower than PA 66 and it has a wider processing temperature range. Its impact strength and solvent resistance are better than PA 66, but its moisture absorption is higher. Many properties are affected by moisture absorption, which must be taken into account when designing with this resin. Various modifiers are added to improve mechanical properties; glass is one of the most commonly used fillers. Addition of elastomers such as EPDM or SBR improves impact resistance.

For unfilled grades, shrinkage is of the order of .01 - .015 mm/mm (1 - 1.5%). Addition of glass fibers reduce the shrinkage to as low as 0.3% in the flow direction (but could be as high as 1% in the cross-flow direction). The post-molding shrinkage is affected mainly by the crystallinity level and moisture absorption. The actual shrinkage is a function of part design, wall thickness, and processing conditions.

Major Manufacturers

BASF (Ultramid B), DuPont (Zytel), DSM (Akulon)